PRODUCTS

Cast and pig iron

Ferroalloys

• Ferroaluminum FA30
• Ferrochrome high carbon FeCr800
• Ferrochrome low carbon FeCr005
• Ferrochrome low carbon FeCr010
• Ferrochrome low carbon FeCr025
• Ferrochrome medium carbon FeCr200
• Ferromanganese FeMn78
• Ferromanganese FeMn88
• Ferromolybdenum FeMo60
• Ferroniobium FeNb60
• Ferrosilicon FeSi10
• Ferrosilicon FeSi45
• Ferrosilicon FeSi65
• Ferrosilicon FeSi75
• Ferrotitanium FeTi35
• Ferrotitanium FeTi70
• Ferrotungsten FeW70
• Ferrovanadium FeV50
• Ferrovanadium FeV80
• Silicocalcium
• Silicomanganese SiMn17

Graphite and graphite electrodes

Modifiers for steel and cast iron

Non-ferrous metals

Ferrotitanium is an alloying alloy of iron and titanium, obtained by reduction or remelting. Ferrotitanium is used in the manufacture of steel for alloying, degassing and deoxidation. Typically, steel containing ferrotitanium has improved mechanical properties.

Brands (GOST)	Mass fraction, %
	Ti	Al	Si	C	P	S	Cu	V	Mo	Zr	Sn	Mn	Cr
		no more
FeTi70S05	68-75	5	0.5	0.20	0.05	0.05	0.2	0.6	0.6	0.6	0.10	-	-
FeTi70S08	68-75	4	0.8	0.30	0.03	0.03	0.3	1.8	2.0	1.5	0.15	0.8	0.8
FeTi70S05Sn03	65-75	5	0.5	0.30	0.03	0.03	0.3	2.5	2.5	1.0	0.30	-	-
FeTi70S1	65-75	5	1.0	0.40	0.05	0.05	0.4	3.0	2.5	2.0	0.15	-	-

Marks (ISO)	Mass fraction, %
	Ti	Al	Si	Mn	C	P	S	V
		no more
FeTi70	65.0-75.0	0.5	0.10	0.20	0.20	0.03	0.03	0.50
FeTi70Al2	65.0-75.0	2.0	0.25	1.00	0.20	0.04	0.04	1.50
FeTi70Al5	65.0-75.0	5.0	0.50	1.00	0.30	0.05	0.04	-

Ferrotitanium is supplied in the form of crushed and sieved particles. Particle size ranges should be as shown in the following table (the mass of the under-size product is established for the point of delivery of the material to the buyer):

Size class	Size of pieces, mm	Mass fraction of product in the batch, %, no more
		oversize	under-slat
1	3.15 - 200	10 No piece shall exceed 1.15 times the maximum limit of the specified particle range in two or three directions.	8
2	3.15 - 100		8
3	3.15 - 50		8
4	3.15 - 25		10
5	3.15 - 10		15
6	up to 6.3		-
7	up to 3.15		-

Ferrotitanium is produced in pieces weighing no more than 15 kg. The amount of fines passing through a sieve with mesh sizes of 10x10 mm should not exceed 6% of the total mass of the batch for ferrotitanium grades FTi70S05, FTi70S1 and FTi70S08. In the manufacture of ferrotitanium for the production of welding materials, the amount of fines is not standardized.

Pieces of ferrotitanium, both in the fracture and on the surface, should not be contaminated with sand, slag and other foreign matter materials.
Traces of non-stick materials and oxide film are allowed.

ГОСТ 4761-91 (416 Кб)

Metallurgical company "Mitra" LLC offers from stock Ferrotitanium FeTi70 at a negotiated price.